John Deere X167

V-twin engine

High-quality air filter

A 724-cc (44.2-cu in.), 12.36 kW at 3350 rpm V-twin engine provides plenty of power and torque to handle tough mulching, mowing, and bagging conditions:

• John Deere Easy Change™ 30-second oil change system to make changing the engine oil easy, quick, and clean.
• V-twin cylinder design for greater torque, lower vibration, and improved sound quality
• Cast-iron sleeves for longer engine life
• Overhead valves for excellent power and fuel economy

Engine speed control

• Electronic ignition for fast starts
• Spring-return feature to ensure the operator will not mistakenly leave the throttle lever in the choke position
• Full-pressure lubrication prolonging engine life and extending the time between oil changes
  • Also more effective when operating the tractor on an incline
• Large, high-quality air filter element extends engine life and is easy to service

FUEL TANK

Convenient fuel-filler opening

• Capacity is 9 L (2.4 U.S. gal.)
• Large-diameter fuel-filler opening is conveniently located under the tractor seat
• Filling the tank without spilling is easy.
• A tethered fuel tank cap is more convenient.
• The sealed fuel cap helps keep vapors inside the tank.

John Deere Easy Change 30-second oil change system (X167 only)

The John Deere Easy Change 30-second oil change system makes changing the engine oil easy, quick, and clean. Changing the oil is as easy as twisting on a new oil-filled filter. Oil does not need to be drained from the engine.

The John Deere Easy Change filter is an additional engine oil reservoir. Changing the filter removes the captured contaminants and replaces about 0.76 L (0.8 qt) of the engine oil.

The functionality does not stop with ease of use. The Easy Change oil system has several meaningful benefits over the traditional oil filter system of the X100 Series:

• A synthetic filter material is used for more predictable filtering and longer life.
• Filtering capacity is greater than with a standard oil filter.
  • More filter surface area
  • More oil flow capacity
• The system has 40 percent more oil volume.
• The oil and engine run cooler.
• The oil filter valve closes whenever the engine stops, so filtered particles are captured and cannot drain back into the engine.
• The risk of spilling during oil service is greatly reduced.
• Waste oil (and new oil production) is reduced by over 453,592.4 kg (1,000,000 lb) per tractor production year.
• This system is not a compromise to just make oil changes easier—these engines pass the same expectations and rigorous testing as always.

Partly due to these improvements, it is not necessary to remove and dispose of all the oil in the engine during service.

Everyone who uses the John Deere Easy Change system saves time and avoids the mess of a traditional oil change. In the past, many 100 Series Lawn Tractor owners rarely or never got around to changing their engine oil. With John Deere Easy Change, even owners who previously would not consider changing the oil themselves can easily do it now. The Easy Change 30-second oil change system is a no-mess, no-fuss solution the competition cannot match.

Installation instructions are in the Operator’s Manual and in the John Deere Easy Change service part box.

Please recycle. Many local government recycling programs, authorized retailers, auto-service centers, and auto-parts stores will puncture and recycle used oil filters and oil.

Solid one-piece frame

Solid one-piece frame

The solid, one-piece frame is constructed of 12-gauge, 2.66-mm (0.105-in.) steel:

• Full-length, robotically welded frame design has high-strength steel rails for added strength and long life.
• One-piece steel fender deck is bolted to the frame.

CAST-IRON FRONT AXLE WILL NOT BEND

Front axle and wheel spindle

The front axle is constructed of solid cast iron that will not bend:

• Automotive-like steering system with sector and pinion steering gears provide a very strong, low-effort, and tight-turning system.
• Three grease fittings, on both steering spindles and the center pivot, allow for regular lubrication to help maintain easy steering and minimize wear.
• Large, 19-mm (0.75-in.) diameter wheel spindles provide excellent durability.

HOOD WILL NOT DENT OR RUST AND INCLUDES QUALITY HEADLIGHTS FOR GOOD VISIBILITY

One-piece hood opens for service access

Quality headlights for good visibility

The hood is made of molded-in color material:

• Reduces sound
• Will not rust or dent
• Openings in the hood let in plenty of cooling air while keeping the sound level low
• Two headlights provide good lighting for nighttime operation

Hydro/automatic two-pedal speed/direction controls

A Kanzaki® Tuff Torq® hydrostatic transmission gives an infinite choice of speeds and makes changing the direction of travel easy. Side-by-side foot pedals control the speed and direction of travel:

• Automotive-type accelerator control ensures easy operation.
• The operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

Hydrostatic transmission

Hydrostatic transmission

Appropriate transmissions are used in each model, depending on rear tire size and tractor performance requirements, to ensure excellent performance and reliability:

• Tuff Torq TLT200 - X107 and X127
• Tuff Torq K46 - X167, X117R, X147R, and X167R

Operator station is designed for comfort

Operator station is designed for comfort

The operator station is designed for operator comfort and easy operation:

• Controls are positioned where they are easy to reach and use to control the tractor.
• The steering wheel is positioned and angled to give the operator plenty of room and steering comfort.
• The seat is tilted back at the optimum angle to provide the most comfortable operator position.

Steering wheel and dash

Wide footrest with debris channels

Controls are easy to see and use:

• Large, 35.6-cm (14-in.) deluxe steering wheel provides greater operator comfort and control.
• Ignition switch is on the dash for starting ease.
• Easy-to-read fuel gauge on the dash makes keeping track of fuel level convenient.

Wide footrest areas with non-slip, anti-vibration rubber floor mats are provided for operator comfort and safety:

• Optimum operator comfort
• Debris removing channels help keep the footrest area clean and dry

Comfortable seat

Seat fore-aft adjustment

Operator comfort is enhanced with a 38-cm (15-in.) high-back, two-piece seat with an open back for good support:

• Especially helpful when operating the tractor for extended periods of time
• Easily adjusted forward or rearward while in the seat
• Seat travel of 14 cm (5.5 in.) and 10 different positions to adjust for operator height

Seat raised for storage and fuel access

The seat can be tilted forward for protection from the elements and to provide easy access to the fuel tank.

Beverage holder and storage with cover

Storage compartment with cover open

A beverage holder and storage compartment are located on the right fender for operator convenience.

Steering wheel and controls

Easy-to-read fuel gauge and hour meter

INSTRUMENTS AND CONTROLS

The contoured dash is functional and attractive:

• The hour meter makes it easy to tell when oil changes and other maintenance should be performed.
• Controls are color coded and labeled for easy identification by the operator.
• Controls are logically placed and easy to reach.
• The functional design of the controls provides good appearance and a comfortable feel.

EASY-READ FUEL GAUGE SHOWS FUEL LEVEL ON THE DASHBOARD

Convenient fuel-filler opening

Easy-read fuel gauge showing full tank

The easy-read fuel gauge shows how much fuel is in the tank and can be seen on the dashboard:

• Easy to check fuel level
• Convenient location
• Visible in cloudy or dusk conditions (is not backlit)
• Will not slosh from bumps
• The hour meter is also visible on the fuel gauge display

MOWER DECK HEIGHT ADJUSTMENT

Mower deck height adjustment lever

A spring-assisted, low-effort lift lever simplifies setting and adjusting the mower cut height:

• Increments of 0.64-cm (0.25-in.) allow the operator to fine-tune the cut height.

TRANSMISSION CONTROL

Side-by-side foot pedals

Two side-by-side pedals control the speed and direction of travel:

• Automotive-type accelerator control ensures easy operation.
• The operator can change direction without lifting foot off the platform.
• Large pedal surface gives superior operator comfort.

CRUISE CONTROL

Cruise control lever

Cruise control maintains the tractor's speed for mowing larger areas.

• To engage, lift up on the cruise lever and hold until the foot is removed from the forward pedal.
• The cruise control can be released by pushing on the brake pedal or the forward pedal.

ELECTRIC POWER TAKE-OFF (PTO) CLUTCH IS EASY AND CONVENIENT TO USE

PTO clutch switch

The heavy-duty electric PTO clutch is operated with a convenient dash-mounted switch.

PARKING BRAKE CONTROL

Parking brake lever

Brake pedal

The parking brake control is conveniently located for easy access. It holds the brake pedal securely in the locked position.

One-piece hood is easy to open

Service interval decal located under hood

The one-piece hood opens easily to permit checking and servicing the engine:

• Important service points are located within easy reach.
• A service-interval decal is provided inside the tractor hood for convenience when servicing the tractor.

Easy-to-service engine oil filter

Seat tilted up for easy access to fuel-fill opening

The engine fuel and oil filters and the oil check/fill tube are exposed for serviceability when the hood is opened. The John Deere Easy Change™ 30-second oil change system makes changing the engine oil easy, quick, and clean. Changing the oil is as easy as twisting on a new oil-filled filter. Oil does not need to be drained from the engine.

The seat tilts up to protect it from the weather and for adding fuel.

RIO switch

Mowing while backing up is strongly discouraged.

The operator who deems it necessary to keep the mower (or other implement) engaged while backing up should first bring the tractor to a stop and look behind the tractor to be sure there are no bystanders. Then actuate (push in) the RIO button. The RIO button must be held down in the reverse implement position as the shift lever is moved into reverse (reverse foot pedal is depressed on models with a hydrostatic transmission).

The operator may then release the button and the mower will continue to operate while backing up and when resuming forward operation. This procedure must be repeated the next time the operator chooses to keep the mower engaged while backing up. If the mower power take-off (PTO) is engaged and the operator shifts into reverse or depresses the reverse pedal prior to pressing the RIO button, ignition to the engine will be shut off. The engine will stop unless the operator either pushes on the RIO switch or shifts out of reverse.

If the engine does stop, the operator must return the mower engagement (PTO) switch or lever to the off position, depress the brake pedal, and then turn the ignition switch to restart the engine.

Rear CargO Mount system

Rear CargO Mount system

The rear CargO Mount system provides convenient and easy installation of the rear bagger.

122-cm (48-in.) Edge cutting system (shielding removed to show mower drive)

The Edge Cutting System has been trademarked to emphasize the advantages of the John Deere mower deck designs. They give superior convenience, performance, and reliability:

• Deep-deck mower design lifts grass for a clean, even cut.
• Smooth underside of mower prevents grass buildup and evenly disperses grass clippings.
• The rolled outer edge of the deck provides extra strength and protection.
• Dual-stage E-coat and powder paint coatings provide extra protection from rust.

The 122-cm (48-in.) Mower Deck is a three-spindle design with heavy-duty characteristics:

• Four mower wheels are standard equipment for a smooth mowing job, even in rolling terrain.
• Flexible discharge chute minimizes property and mower deck damage.
• No tools are required to go from mulching (with mulch cover) to side discharge to rear bagging.
• The rugged 12-gauge, 2.7-mm (0.105-in.) steel mower will provide years of dependable mowing.
• The blade-to-spindle design provides a unique mounting system for the mower blade that gives extra safety and convenience.
• A mulching cover is standard equipment.
• A high-performance mulching blade is available to enhance mulching performance.

MOWER WASH PORT

Mower wash port

A wash port is provided to make cleaning the underside of the mower deck easy:

• A hose connector can be purchased locally for connecting to the wash port.

STARLOCK™ BLADE DESIGN

StarLock blade design

The StarLock blade design keeps the blade bolt at the correct torque for easy removal.

Optional blades are available for difficult mulching or bagging conditions.

MOWER DECK HEIGHT ADJUSTMENT

Mower deck height adjustment lever

A spring-assisted, low-effort lift lever simplifies setting and adjusting the mower cut height:

• Increments of 6 mm (0.25 in.) allow the operator to fine-tune the cut height.
• A cut-height range of 25 to 100 mm (1 to 4 in.) allows the operator to choose the optimum cutting height for each condition.
• The handle is carefully designed for easy use and to not interfere with entering or exiting the operator station.

OPTIONAL BAGGER

230-L (6.5-bu) bagger

230-L (6.5-bu) bagger

A cut-and-throw, 230-L (6.5-bu) bagger is sold separately.

The bagger kit can be set up without tools in minutes, provides efficient bagging performance, and has easy-to-empty bags.

Special bagging blades are not required but are available for enhanced performance.